Efficient & permanent plant marking: With just one flexible printing system
In industry, all technical parts and components of a plant must be permanently marked. Plant marking can therefore be roughly divided into: Equipment marking, cable marking and safety marking. These 3 fields of markings should be taken into account by a plant identification system.
At Texit, we have been specializing in industrial marking for over 20 years. As a manufacturer of cable markers, we have an in-depth understanding of industrial requirements and standards in the field of marking and offer you the opportunity to design a customized marking system specifically for your plant and machinery. You will benefit from our Texit service and high product quality from day 1.
✔️ Shrink sleeve markers specified according to EN 50 343 and CEN/TS 45545-2
✔️ Flexible labeling of different cable types & system components directly on site with only one thermal transfer printer - stainless steel lasered or embossed
✔️ Fabric labels, nameplates for flexible labeling of built-in devices inside and outside the plant
✔️ Efficient troubleshooting through easy identification of individual components & parts
✔️ Time & cost savings for subsequent maintenance / repair & replacement work.
✔️ Easy assembly during installation
✔️ Wide range of extremely robust products with long service life
✔️ Benefit from our Texit service & technical support in the long term
This is what our labeling expert Drazen Milosevic says
Equipment labeling can be simple and straightforward if a printing system is used that can be used flexibly.
This has enabled my customers in plant engineering to significantly reduce the time and costs involved in labeling. A system that can do everything - it couldn't be simpler.
NEW: Cable markers without cable ties
With our new HTX-KM cable markers without cable ties, you can save on mounting aids or accessories in future. Thanks to the ingenious locking loop, these markers made of robust plastic can be easily attached to cables. Halogen-free, UV-resistant and ideally suited for long-term use in difficult conditions.
Rugged heat shrink marker
Texit shrink sleeve markers are particularly suitable for marking electronic components and devices within a plant. These can be easily and flexibly labeled as desired using the thermal transfer printing process and mounted on the corresponding cables. As far as fire protection is concerned, the halogen-free markers are particularly well suited, as no toxic gases are produced in the event of a fire.
Cable marker
The HTX-KM cable markers can be used to mark power cables and lines of industrial systems in a permanently legible manner. The markers flexibly adapt to the cable diameter and can be easily labeled with a thermal transfer printing system. They are made of robust polyether polyurethane and are halogen-free and UV-resistant.
Printable nameplates
GRT nameplate labels are ideal for maintaining an overview of the entire system and all associated machines. These plastic labels are self-adhesive and do not require a label holder. They can be printed with information on individual machines and devices using a thermal transfer printer so that they are permanently legible. In addition to their high quality and durability, these identification labels are also easy to install.
Flexible labels for cables
Self-laminating cable labels are suitable for cable marking in industrial plants. These products can be printed in one step and then applied directly to the relevant cables and wires. And this is also possible subsequently, after cable installation.
Plant identification
Stainless steel markers for extreme requirements
Work on equipment in industry often happens under extreme requirements. Therefore, the durability of the products is very important in industrial marking. Stainless steel markers have a much higher robustness than plastic and are therefore particularly suitable in a working environment with extremely high demands on durability. Our stainless steel markers are available in lasered and embossed versions.
Warning signs for safety
Safety labeling is also an integral part of plant labeling in industry. Typical warning signs are particularly suitable for warning employees of hazards or pointing out operating errors. Thanks to the signal yellow color, these signs are immediately noticed by users when operating machines & co. It is also practical that the warning signs from Texit can be labeled with the same printing system as labels and cable markers.
Robust labels
Labels also play an important role in the marking of plants and industrial systems. They can be applied to machines and devices as well as to pipelines or individual components. It is not absolutely necessary to specify certain areas of application for labels, as they can be printed flexibly and used in a wide variety of ways. With just one system, labels as well as cable markers, shrink sleeves and type plates can be permanently printed quickly and flexibly.
Looking for more products for plant identification?
Discover our full range of equipment labeling.
Industrial plant identification made easy
Equipment marking in industry can be fast, simple and straightforward. At Texit, in addition to excellent product quality, we guarantee our customers a special service. You get a trained expert as a fixed contact person, who advises you on the suitable products and also looks after you afterwards, solves problems and optimizes the use of our products on site at your premises.
As an ISO-certified company, you can rely on our 20 years of experience in the field of industrial labelling.
